Hướng dẫn lắp đặt màn hình Tesla cho Chevy Silverado 2019–2023: Hướng dẫn Android Radio 29 bước

What does this installation actually involve?

The job is not a simple screen swap. The factory center stack is removed in stages, several original modules are transferred into the new fascia, the original connectors are reconnected through the matched wiring route, and the screen is tested before the dashboard is closed.

Steps 1–11: remove the original Silverado center stack

Follow the order. Do not jump directly to the screen or pull the complete center panel before its surrounding trim and connectors are released.

Step 1 · Screw Caps & Fasteners

Remove the screw caps and fastening screws

Start with the fasteners securing the trim panels on both sides of the dashboard.

HãyRemove the screw covers and the fasteners underneath them.

WhyThe side trim cannot release correctly while these screws remain installed.

Kiểm traConfirm the visible side-trim fasteners are completely removed.

Dừng: do not pull hard on the side panel while a fastening screw is still installed.

Step 2 · Side Trim Panels

Release the left and right trim panels

The trim is retained by clips after the screws are removed.

HãyPull the left and right trim panels away from their retaining clips.

WhyThis exposes the center-console removal path.

Kiểm traClips remain intact and the panels are fully free.

Dừng: if one section stays rigid, check again for an unreleased clip or fastener.

Step 3 · Front Center Console Trim

Lift the front center-console trim upward

The reference sequence lifts this panel upward to release it from the console.

HãyLift the front trim upward until it detaches from its mounting points.

Kiểm traThe trim is loose but still supported until its connector is disconnected in Step 4.

Step 4 · Console Connector

Disconnect the center-console connector

Do not move the removed trim away until its electrical connection has been released.

HãyPress the connector release and unplug the console connection.

Kiểm traNo wire remains attached to the panel before you place it aside.

Do not: pull the connector out by its wires.

Step 5 · Lower Console Trim

Remove the trim at the bottom of the center console

This lower trim covers the next section of the center-stack assembly.

HãyRelease the lower trim carefully from its clips.

Kiểm traThe lower edge of the main center-console trim is now accessible.

Step 6 · Main Center Trim

Remove the center-console trim panel

With the surrounding pieces already removed, release the main center trim.

Kiểm traThe panel separates without bending or pulling connected wiring.

Step 7 · Mounting Screws

Remove the center-console mounting screws

The original control assembly remains mechanically secured until these screws are removed.

HãyRemove the exposed center-console mounting screws.

Kiểm traThe original center control panel is no longer mechanically locked in place.

Step 8 · Center Control Panel

Remove the original center control panel

Support the panel because several original connectors are still attached behind it.

Continue whenYou can access the rear LVDS/media, climate and lower-function connectors.

Step 9 · Original Display

Disconnect the original display LVDS / media-button connection

This is the factory display-data route that will later be integrated with the vertical-screen system.

Kiểm traThe connector and its locking structure remain undamaged.

Dừng: an LVDS-style connector should not require force or pin modification.

Step 10 · Climate Plug

Disconnect the original air-conditioning connector

Release the original climate-control plug from the removed center-control assembly.

Kiểm traNo bent pins, damaged locks or pulled wires.

Step 11 · Lower Factory Connections

Disconnect the hazard, USB and cigarette-lighter connections

These lower factory connections must be unplugged before the original modules can be transferred.

HãyDisconnect the hazard-button, USB-port and cigarette-lighter/power connections that match the supplied installation route.

Kiểm traEvery retained lower module is electrically free before physical removal.

Steps 12–17: move the original Silverado hardware into the new fascia

Step 12 · Remove Retained Modules

Remove the original vent, power, cigarette-lighter and USB modules

These factory components are reused instead of being discarded.

WhyThe replacement fascia is designed to retain the original vehicle hardware in these positions.

Kiểm traNo factory clip or screw mount is broken.

Step 13 · Cigarette Lighter Module

Remove the cigarette-lighter module correctly

The metal outer housing must be released before the internal module is removed.

Reference sequence: pull the metal shell outward before attempting to remove the inner cigarette-lighter module.

Do not: force the complete socket through the fascia as one locked assembly.

Step 14 · Original Switch Buttons

Remove the original switch-button assembly

The factory function buttons are transferred to the bottom of the vertical-screen assembly.

Kiểm traButton housings, mounting tabs and screws remain intact.

Step 15 · Install Original Buttons

Mount the original vehicle buttons under the vertical screen

Position the factory button module in the corresponding lower opening of the new screen fascia.

Kiểm traThe button assembly sits straight and each physical button moves freely.

Step 16 · USB & Power Modules

Install the original cigarette-lighter, USB and power modules

Install these retained modules into the new fascia in sequence.

Kiểm traUSB and power sockets are secure, straight and do not rotate loosely.

Step 17 · Original Air Vent

Install the original air vent into the vertical-screen fascia

The original Silverado air vent is moved into the corresponding vent location on the new assembly.

Kiểm traThe vent sits flush and its adjustment mechanism moves normally.

Steps 18–21: identify and connect the vehicle-specific wiring

Step 18 · Wiring Definition

Identify the wiring-definition diagram

Before connecting anything, understand what each supplied connection is intended to connect to.

HãyIdentify each labeled connection and compare it with the harness supplied to your order.

Do not guess: unknown wires, pin locations or CAN connections require order-specific confirmation.

Step 19 · Main Unit Wiring

Review the head-unit wiring definition

This diagram covers the main vertical-screen connection side.

Continue whenThe supplied main-unit connectors are positively identified.

Step 20 · Bottom Function Connector

Reconnect the original lower-function connector

The original lower functions disconnected earlier now reconnect through the intended vehicle-specific route.

HowAlign the keyed connector, insert it straight and verify the locking mechanism engages.

Kiểm traThe plug stays locked after a gentle pull on the connector body.

Step 21 · Power / LVDS / Media Alignment

Align the vertical-screen power, LVDS and media connections

These are separate connections and should be identified individually instead of treated as one generic plug.

Kiểm traNo plug is rotated, offset or partly inserted.

Dừng: do not shave, cut or repin a plug to make it fit.

Steps 22–24: mount the screen and complete the audio connection

Step 22 · Install Vertical Screen

Place the wired screen into the center console and tighten the screws

Route wiring into open space behind the dashboard before pushing the unit fully into place.

HowGuide the cable bundles into free space behind the screen, align the mounting points and tighten the screws in sequence.

Kiểm traNo harness is pinched between the fascia and dashboard.

Step 23 · Decorative Panel

Secure the decorative fascia to the vertical screen

Complete the visible center-stack assembly only after the screen is correctly seated.

Kiểm traThe fascia sits flush, vents move normally and retained buttons are not trapped.

Step 24 · AUX to USB Audio

Connect the audio-output AUX route to the original USB port

This is a specific part of this Silverado audio route and should not be hidden inside the general wiring section.

WhyThe Android unit can power on normally but still have no sound if this audio route is incomplete.

Kiểm tra phiên bản: use this route only when the adapter supplied with your iKAGOO order matches the photographed type.

Step 25: what if the original Silverado interface displays incorrectly?

The reference sequence does not jump straight to changing settings. It first checks the original LVDS route, then confirms the original vehicle screen size.

Step 25 · Abnormal Original Interface

Open the vehicle-information display settings only after checking the hardware

If the original vehicle interface looks stretched, incorrectly scaled or abnormal, begin with the display connection.

Triệu chứngOriginal Chevrolet interface is stretched, compressed, offset or otherwise displayed incorrectly.

Đơn hàngCheck the LVDS connection first; change the original-screen configuration only after the physical connection passes.

Step 25.1 · Original LVDS

Inspect the original vehicle LVDS connection

A loose original display-data connection can create a display problem that software settings will not fix.

Kiểm traCorrect orientation, complete insertion and a secure connector lock.

Step 25.2 · LVDS / Power Route

Check the corresponding LVDS / power connection

Verify the second side of the display route before changing the factory-screen size.

Continue whenBoth sides of the display connection are secure.

Step 25.3 · Original Screen Size

Set the original factory display size to match the truck

The documented Silverado route distinguishes between factory 7-inch and 8-inch displays.

Reference sequence: if the original display is 8 inches, select the 8-inch option; if it is 7 inches, select the 7-inch option. The reference procedure then turns the ignition off and locks the vehicle to allow the system to cycle.

iKAGOO boundary: do not copy unrelated CAN, engineering or hidden values. If your menu differs, request the correct path using your iKAGOO order number.

Step 26: how do you switch audio and diagnose no sound?

The original sequence contains three distinct audio checks. They should not be collapsed into one vague “check audio” instruction.

Step 26.1 · Adapter Connection

Inspect the audio-output and USB adapter connection

Confirm the audio adapter is correctly connected to the vehicle's original USB route.

Kiểm traBoth adapter connections are fully seated and the factory USB route is being used as intended.

Step 26.2 · USB Audio Converter

Activate the USB audio converter when your supplied adapter matches this type

The documented adapter uses a physical switch-button procedure.

Reference procedure: press and hold the USB audio-converter switch for approximately 5 seconds, then release it. The documented converter should show a flashing blue indicator.

Only do this when: the USB converter supplied with your iKAGOO order is the same type and the applicable instructions confirm this procedure.

Step 26.3 · Source Switching

Switch the original vehicle audio source, then test Android playback

The factory audio source must be on the correct USB/AUX route before Android playback is tested.

Kiểm traPlay a known music source in Android and verify stable output through the factory audio system.

If there is still no sound: send the order number plus photos/video of the audio adapter and USB connection to iKAGOO instead of changing unrelated vehicle parameters.

Step 27: what if the original reverse interface does not appear?

Step 27 · Identify the Reverse Symptom

Check whether the original reverse screen is missing or Android reverse appears instead

The documented route treats this as a local-reverse configuration issue after the physical camera/interface connections have been checked.

FirstVerify the matched reverse-camera/interface wiring is connected correctly.

ThenCheck the local-reverse setting only if the physical connection is correct.

Step 27.1 · Factory Settings

Open the applicable factory-settings menu

The reference installation enters factory settings at this point to check the reverse configuration.

iKAGOO rule: do not assume a third-party factory password, CAN setting or hidden menu value applies to your unit. Use the order-specific instruction supplied for your iKAGOO hardware version.

Step 27.2 · Local Reverse

Verify the Local Reverse option for the matched configuration

The documented procedure disables Local Reverse when the retained original reverse interface is required.

Reference logic: when the original reverse interface should be retained, the documented configuration checks that Local Reverse is disabled.

Bài kiểm tra cuối cùngShift into reverse while stationary and verify the intended camera interface appears reliably.

Order-specific: if your supplied iKAGOO configuration uses a different camera route, follow the configuration assigned to that order.

Step 28: configure the original Silverado buttons correctly

The documented installation distinguishes between factory 7-inch and 8-inch configurations because their original control-panel button functions can differ.

Step 28 · Determine the Original Panel Type

Confirm which original display and button layout the truck had

Do not select a panel style only because the replacement screen looks the same.

WhyThe original 7-inch and 8-inch layouts can use different factory button functions.

Step 28.1 · Activate Panel Settings

Open Vehicle Information and activate the factory-panel settings function

This is the configuration area used to match the retained original controls.

Kiểm traThe menu corresponds to the hardware/version shipped with your order.

Step 28.2 · Select Panel Style

Select the panel style that matches the actual original vehicle buttons

The documented menu provides two panel styles for the two original button arrangements.

Reference procedure: use the left arrow to switch between the available styles, select the layout matching the actual installed vehicle and confirm with OK.

Kiểm traPress every retained physical button individually and verify that the intended function responds.

Dừng: if buttons are mapped incorrectly, do not select random CAN or vehicle profiles. Request the correct configuration using the iKAGOO order number.

When is the Chevy Silverado Tesla Screen installation complete?

The dashboard should only be fully closed after the physical installation, original vehicle functions and Android functions all pass testing.

This guide is only for the corresponding iKAGOO-supplied hardware

Product and installation support

Technical scope: Chevrolet Silverado vehicle-specific vertical Android-screen installation · iKAGOO public fitment range: 2019–2023 · Covers dashboard disassembly, original module transfer, wiring, AUX-to-USB audio, original 7″/8″ display configuration, reverse-interface setup, factory-panel configuration and final testing. Last reviewed: September 7, 2026.